DRYER VENT CLEANING Glendale Arizona

On average, duct cleaning costs around $370, sometimes between $268 and $485, depending on the size, condition, or difficulty it takes to clean the duct. However, larger homes or those that have more ducts or contamination maybe charge up to $700.

• Mold may grow inside the hard surface of the ducts or on other components of your heating and cooling system.
• Ducts may be infested with vermin like rodents or insects.
• They can be clogged with excessive amounts of dust and debris and/or particles, which can impede the performance of your ducts.

Yes, you may clean the ducts yourself. However, you might encounter difficulty in properly dealing with the components and materials inside it. When it comes to the nitty-gritty of cleaning the duct, it is not a do-it-yourself job. You will need professional tools that are not readily available in your garage, such as a high-powered vacuum and rotary brushes.

Ventilation systems can be categorized as one of four types, namely, exhaust, supply, balance, and heat recovery.

In general, installation of a ventilation system can cost between $300 and $500 per room.

Technically, ventilation is the mechanical system in a house or building that supplies “fresh” outdoor air, and removes the “contaminated” indoor air. Ventilation is used to control exposure to airborne contaminants, such as fumes, specks of dust, and vapors, which can be risky especially to those with respiratory problems.

Most homeowners spend about $80 to $200 to install or replace a dryer vent. This estimate includes labor and materials. The total project cost can go up to $1,000, depending on some factors like material quality, placement, and installation complexity.

Here is a simplified process on how to fix, repair, or replace a dryer vent:

1. Gather your supplies (screwdriver, washcloth, duct tape, plumbing snake, trash can)
2. Empty and wash lint trap
3. Pull dryer away from the wall
4. Check duct for rips and gaps
5. Tighten seals at both ends of the duct
6. Replace a damaged or non-sealing duct (optional)
7. Clear the duct channel
8. Try the dryer again

Yes, plumbers can be hired to install dryer vents. However, we have dryer vent professionals who are more experienced in doing the job and know more its what’s, how’s, and whereabouts.

Yes, you can patch a dryer vent to prevent it from further breaking. Ducts that are broken can be fixed easily by sealing the damaged area. However, the repair will depend on the size of the broken area. If it is relatively small, a simple wrapping of a duct tape would suffice. On the other hand, if the damage goes to the extent that a duct tape is not sufficient, then it is best to install a new vent duct and replace the old one.

1. To access the flexible gas line on a gas dryer, ask a helper to lift the dryer away from the wall. Turn off the gas valve at the gas pipe. Using an adjustable wrench, disconnect the fitting where the line attaches to the valve. Unplug the power cord from the outlet if you have an electric dryer.
2. Move the dryer as needed to gain access to the back and the circular exhaust pipe where the vent tube connects. The disconnected flexible vent tube should be nearby, and the open end of the tube may still have the clamp attached.
3. Using a nut driver, loosen the clamp’s bolt counterclockwise. Remove the clamp from the vent tube’s end.
4. Insert a new vent clamp 3/4 inch from the open end of the tube. Fit the tube completely onto the circular exhaust pipe while holding it towards the open end. Tighten the clamp’s bolt to connect the vent pipe to the dryer exhaust.
5. If necessary, reposition the dryer to reconnect the flexible gas line fitting to the natural gas valve. Using the wrench, tighten the fitting securely. Turn on the valve. Plug an electric dryer’s cord into an electrical outlet.
6. Place the dryer in the desired position, being careful not to crush the vent tube between the wall and the back of the dryer.